1. You will then be able to get Odin V3.1.0 and Samsung ROOT A260G U1 8.1.0 Frp Off Oem Off FileFile after extracting the zip file.
2. Power off your Samsung device.
3. Then, press and hold Power Key, Home Key, and Volume Down Key at the same time.
4. When prompted as shown, press the Volume Up key to continue the process and you will enter Download Mode.
5. Step 2 Perform Odin3 and Connect Samsung Device to PC.
6. Launch Odin3, and connect your Samsung via USB cable to PC.
7. Once you have connected your handset to the computer, Odin3 will automatically recognize the device and prompt "Added" in the lower-left panel.
8. Now, click on the "AP/PDA" button and select the file extracted in advance.
9. After that, click on the "Start" button to begin the rooting process.
10. It will take a few seconds to finish rooting, and when it finished, the green "PASS" will inform you that the rooting process is finished.
11. When your Samsung phone is on anew, there will be a SuperSu app showed on the screen which means you've succeeded in rooting.
12. Besides, you can check out the root status by using
13. What if it fails to get root on your Samsung phone, check out the solutions below.
14. 1. Restart your PC and install Samsung USB Driver, and try to reconnect.
15. That's all about getting rooted in Samsung phones with Odin3.

1. Download the relevant USB driver for your Samsung device.
2. Download the flash tool Odin on your phone.
3. Now, download the relevant ADB Enable File for your device.
4. Open the Odin software then choose ADB Enable File in “AP” from the Box.
5. Turn on USB debugging mode on your phone.
6. Now, connect your mobile and computer with a USB cable.
7. Open the ADB Enable tool and click on the start. After that, your device will start rebooting.
8. Disconnect the USB cable.
9. Select language English when your phone turns on. After that, click next.
10. Now turn on Wi-Fi or mobile data.
11. After that, agree on the agreements and click on next. They will ask you to verify your account.
12. Now, connect your mobile and PC again. Then open the Atozflashfile.com..
13. You will see some information about your mobile phone and the operating system.
14. Click on remove FRP. The lock will be removed in a short time.
15. Congratulations, you have successfully bypassed the FRP lock.

• right-click to "Open as Administrator"

Follow these steps to enter Download Mode/Odin Mode

1. Power off your device
2. Press and hold Volume Down key, Home Key and Power Key
3. When your device vibrates, release Power key while keep holding the Volume Down key and the Home key
4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)

Your device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime, you should see a light-blue box at the ID: COM section stating "COM:3" (the number depending on which USB port you have plugged the device cable and is irrelevant).

Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either BL"AP"CP"CSC

After adding the file, click "Start" to begin the flashing process

Click "Start" to flash.

DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.

When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device

Flash succeeded

ROOT A205Y U2 9

Download Link:: Link

1. You will then be able to get Odin V3.1.0 and Samsung ROOT A260G U1 8.1.0 Frp Off Oem Off FileFile after extracting the zip file.
2. Power off your Samsung device.
3. Then, press and hold Power Key, Home Key, and Volume Down Key at the same time.
4. When prompted as shown, press the Volume Up key to continue the process and you will enter Download Mode.
5. Step 2 Perform Odin3 and Connect Samsung Device to PC.
6. Launch Odin3, and connect your Samsung via USB cable to PC.
7. Once you have connected your handset to the computer, Odin3 will automatically recognize the device and prompt "Added" in the lower-left panel.
8. Now, click on the "AP/PDA" button and select the file extracted in advance.
9. After that, click on the "Start" button to begin the rooting process.
10. It will take a few seconds to finish rooting, and when it finished, the green "PASS" will inform you that the rooting process is finished.
11. When your Samsung phone is on anew, there will be a SuperSu app showed on the screen which means you've succeeded in rooting.
12. Besides, you can check out the root status by using
13. What if it fails to get root on your Samsung phone, check out the solutions below.
14. 1. Restart your PC and install Samsung USB Driver, and try to reconnect.
15. That's all about getting rooted in Samsung phones with Odin3.

1. Download the relevant USB driver for your Samsung device.
2. Download the flash tool Odin on your phone.
3. Now, download the relevant ADB Enable File for your device.
4. Open the Odin software then choose ADB Enable File in “AP” from the Box.
5. Turn on USB debugging mode on your phone.
6. Now, connect your mobile and computer with a USB cable.
7. Open the ADB Enable tool and click on the start. After that, your device will start rebooting.
8. Disconnect the USB cable.
9. Select language English when your phone turns on. After that, click next.
10. Now turn on Wi-Fi or mobile data.
11. After that, agree on the agreements and click on next. They will ask you to verify your account.
12. Now, connect your mobile and PC again. Then open the Atozflashfile.com..
13. You will see some information about your mobile phone and the operating system.
14. Click on remove FRP. The lock will be removed in a short time.
15. Congratulations, you have successfully bypassed the FRP lock.

• right-click to "Open as Administrator"

Follow these steps to enter Download Mode/Odin Mode

1. Power off your device
2. Press and hold Volume Down key, Home Key and Power Key
3. When your device vibrates, release Power key while keep holding the Volume Down key and the Home key
4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)

Your device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime, you should see a light-blue box at the ID: COM section stating "COM:3" (the number depending on which USB port you have plugged the device cable and is irrelevant).

Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either BL"AP"CP"CSC

After adding the file, click "Start" to begin the flashing process

Click "Start" to flash.

DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.

When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device

Flash succeeded

Samsung ROOT A260G U1 8.1.0

Download Link:: Link

1. You will then be able to get Odin V3.1.0 and Samsung ROOT A260G U2 8.1.0 Frp Off Oem Off FileFile after extracting the zip file.
2. Power off your Samsung device.
3. Then, press and hold Power Key, Home Key, and Volume Down Key at the same time.
4. When prompted as shown, press the Volume Up key to continue the process and you will enter Download Mode.
5. Step 2 Perform Odin3 and Connect Samsung Device to PC.
6. Launch Odin3, and connect your Samsung via USB cable to PC.
7. Once you have connected your handset to the computer, Odin3 will automatically recognize the device and prompt "Added" in the lower-left panel.
8. Now, click on the "AP/PDA" button and select the file extracted in advance.
9. After that, click on the "Start" button to begin the rooting process.
10. It will take a few seconds to finish rooting, and when it finished, the green "PASS" will inform you that the rooting process is finished.
11. When your Samsung phone is on anew, there will be a SuperSu app showed on the screen which means you've succeeded in rooting.
12. Besides, you can check out the root status by using
13. What if it fails to get root on your Samsung phone, check out the solutions below.
14. 1. Restart your PC and install Samsung USB Driver, and try to reconnect.
15. That's all about getting rooted in Samsung phones with Odin3.

1. Download the relevant USB driver for your Samsung device.
2. Download the flash tool Odin on your phone.
3. Now, download the relevant ADB Enable File for your device.
4. Open the Odin software then choose ADB Enable File in “AP” from the Box.
5. Turn on USB debugging mode on your phone.
6. Now, connect your mobile and computer with a USB cable.
7. Open the ADB Enable tool and click on the start. After that, your device will start rebooting.
8. Disconnect the USB cable.
9. Select language English when your phone turns on. After that, click next.
10. Now turn on Wi-Fi or mobile data.
11. After that, agree on the agreements and click on next. They will ask you to verify your account.
12. Now, connect your mobile and PC again. Then open the Atozflashfile.com..
13. You will see some information about your mobile phone and the operating system.
14. Click on remove FRP. The lock will be removed in a short time.
15. Congratulations, you have successfully bypassed the FRP lock.

• right-click to "Open as Administrator"

Follow these steps to enter Download Mode/Odin Mode

1. Power off your device
2. Press and hold Volume Down key, Home Key and Power Key
3. When your device vibrates, release Power key while keep holding the Volume Down key and the Home key
4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)

Your device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime, you should see a light-blue box at the ID: COM section stating "COM:3" (the number depending on which USB port you have plugged the device cable and is irrelevant).

Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either BL"AP"CP"CSC

After adding the file, click "Start" to begin the flashing process

Click "Start" to flash.

DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.

When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device

Flash succeeded

Samsung ROOT A260G U2 8.1.0

Download Link:: Link

1. You will then be able to get Odin V3.1.0 and Samsung G930F U6 8.0.0 Root Frp Off Oem Off File after extracting the zip file.
2. Power off your Samsung device.
3. Then, press and hold Power Key, Home Key, and Volume Down Key at the same time.
4. When prompted as shown, press the Volume Up key to continue the process and you will enter Download Mode.
5. Step 2 Perform Odin3 and Connect Samsung Device to PC.
6. Launch Odin3, and connect your Samsung via USB cable to PC.
7. Once you have connected your handset to the computer, Odin3 will automatically recognize the device and prompt "Added" in the lower-left panel.
8. Now, click on the "AP/PDA" button and select the file extracted in advance.
9. After that, click on the "Start" button to begin the rooting process.
10. It will take a few seconds to finish rooting, and when it finished, the green "PASS" will inform you that the rooting process is finished.
11. When your Samsung phone is on anew, there will be a SuperSu app showed on the screen which means you've succeeded in rooting.
12. Besides, you can check out the root status by using
13. What if it fails to get root on your Samsung phone, check out the solutions below.
14. 1. Restart your PC and install Samsung USB Driver, and try to reconnect.
15. That's all about getting rooted in Samsung phones with Odin3.

1. Download the relevant USB driver for your Samsung device.
2. Download the flash tool Odin on your phone.
3. Now, download the relevant ADB Enable File for your device.
4. Open the Odin software then choose ADB Enable File in “AP” from the Box.
5. Turn on USB debugging mode on your phone.
6. Now, connect your mobile and computer with a USB cable.
7. Open the ADB Enable tool and click on the start. After that, your device will start rebooting.
8. Disconnect the USB cable.
9. Select language English when your phone turns on. After that, click next.
10. Now turn on Wi-Fi or mobile data.
11. After that, agree on the agreements and click on next. They will ask you to verify your account.
12. Now, connect your mobile and PC again. Then open the Atozflashfile.com..
13. You will see some information about your mobile phone and the operating system.
14. Click on remove FRP. The lock will be removed in a short time.
15. Congratulations, you have successfully bypassed the FRP lock.

• right-click to "Open as Administrator"

Follow these steps to enter Download Mode/Odin Mode

1. Power off your device
2. Press and hold Volume Down key, Home Key and Power Key
3. When your device vibrates, release Power key while keep holding the Volume Down key and the Home key
4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)

Your device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime, you should see a light-blue box at the ID: COM section stating "COM:3" (the number depending on which USB port you have plugged the device cable and is irrelevant).

Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either BL"AP"CP"CSC

After adding the file, click "Start" to begin the flashing process

Click "Start" to flash.

DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.

When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device

Flash succeeded

1. Download the relevant USB driver for your Samsung device.
2. Download the flash tool Odin on your phone.
3. Now, download the relevant ADB Enable File for your device.
4. Open the Odin software then choose ADB Enable File in “AP” from the Box.
5. Turn on USB debugging mode on your phone.
6. Now, connect your mobile and computer with a USB cable.
7. Open the ADB Enable tool and click on the start. After that, your device will start rebooting.
8. Disconnect the USB cable.
9. Select language English when your phone turns on. After that, click next.
10. Now turn on Wi-Fi or mobile data.
11. After that, agree on the agreements and click on next. They will ask you to verify your account.
12. Now, connect your mobile and PC again. Then open the Atozflashfile.com..
13. You will see some information about your mobile phone and the operating system.

1. You will then be able to get Odin V3.1.0 and Samsung G930F U6 8.0.0 Root Frp Off Oem Off File after extracting the zip file.
2. Power off your Samsung device.
3. Then, press and hold Power Key, Home Key, and Volume Down Key at the same time.
4. When prompted as shown, press the Volume Up key to continue the process and you will enter Download Mode.
5. Step 2 Perform Odin3 and Connect Samsung Device to PC.
6. Launch Odin3, and connect your Samsung via USB cable to PC.
7. Once you have connected your handset to the computer, Odin3 will automatically recognize the device and prompt "Added" in the lower-left panel.
8. Now, click on the "AP/PDA" button and select the file extracted in advance.
9. After that, click on the "Start" button to begin the rooting process.
10. It will take a few seconds to finish rooting, and when it finished, the green "PASS" will inform you that the rooting process is finished.
11. When your Samsung phone is on anew, there will be a SuperSu app showed on the screen which means you've succeeded in rooting.
12. Besides, you can check out the root status by using
13. What if it fails to get root on your Samsung phone, check out the solutions below.
14. 1. Restart your PC and install Samsung USB Driver, and try to reconnect.
15. That's all about getting rooted in Samsung phones with Odin3.

How to Flash

1. Download the relevant USB driver for your Samsung device.
2. Download the flash tool Odin on your phone.
3. Now, download the relevant ADB Enable File for your device.
4. Open the Odin software then choose ADB Enable File in “AP” from the Box.
5. Turn on USB debugging mode on your phone.
6. Now, connect your mobile and computer with a USB cable.
7. Open the ADB Enable tool and click on the start. After that, your device will start rebooting.
8. Disconnect the USB cable.
9. Select language English when your phone turns on. After that, click next.
10. Now turn on Wi-Fi or mobile data.
11. After that, agree on the agreements and click on next. They will ask you to verify your account.
12. Now, connect your mobile and PC again. Then open the Atozflashfile.com..
13. You will see some information about your mobile phone and the operating system.
14. Click on remove FRP. The lock will be removed in a short time.
15. Congratulations, you have successfully bypassed the FRP lock.

• right-click to "Open as Administrator"

Follow these steps to enter Download Mode/Odin Mode

1. Power off your device
2. Press and hold Volume Down key, Home Key and Power Key
3. When your device vibrates, release Power key while keep holding the Volume Down key and the Home key
4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)

Your device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime, you should see a light-blue box at the ID: COM section stating "COM:3" (the number depending on which USB port you have plugged the device cable and is irrelevant).

Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either BL"AP"CP"CSC

After adding the file, click "Start" to begin the flashing process

Click "Start" to flash.

DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.

When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device

Flash succeeded

ROOT A260F U1 8.1.0

Download Link:: Link

Samsung ROOT A205F U1 Android 9