February 2019 - A to Z Flash File

Breaking

Thursday, February 28, 2019

8:15 PM

Samsung SM-J100H MT6572 v4.4.2 Tested Scatter Flash File Free 100%

Samsung SM-J100H MT6572 v4.4.2 Tested Scatter Flash File Free 100% 

Flashing By Sp Flash Tool-CM2MTK-Miracle Box And Any Other Tool
No Dead Risk Dead Fix Virus Clear Hang On Logo Fix
MT6572__samsung__SM-J100H__j13g__4.4.2__ALPS.KK1.MP7.V1
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand   : samsung
Device Model   : j13g
Device CPU     : MT6572
Device IntName : Galaxy J1
Device Version : 4.4.2
Device Compile : 8/12/2015 11:23:54 AM
Device Project : ALPS.KK1.MP7.V1
Device ExtInfo : SM-J100H

How To Flash –Samsung SM-J100H

Perfectly Working You Must Need to Follow Below


  1. Download Latest version Flash Tools
  2. Extract On Your Computer( Any Drive)
  3. Download You Mobile Same Version Firmware
  4. Extract On Your Computer
  5. Install Your Phone USB Driver On Your Pc
  6. Now Open SP Flash Tools On Your Pc
  7. Load Scatter File Frome Extract Firmware Location
  8. Click Download And Update Button
  9. Now Connect Your Phone With Your PC USB Cable
  10. Your Phone Star Flashing Wait for 5/7 Minute
  11. When Complete Flashing Process Then You Green Ring Will Paper
  12. Now Complete Your Phone Updated
  13. Remove USB Cable & Enjoy Mobile Phone
  14. Don’t Forget Comment & Share Thank You
Warning Note: Fast Backup Your Phone Important Personal Data When Flash Your Phone Erase All Data File. So Please Fast Backup Data And Flashing Your Phone Own Risk.

Samsung SM-J100h Flash File



Following are the steps to perform in order to Flash Stock Rom or any other custom ROM using so called flash tool SP(Smart Phone) Flash Device on a windows computer. Before starting the process of flashing make sure that your smartphone device has at least 50 percent of battery.

  1. Extract the flash file in any folder on your computer or laptop device.
  2. Need to install SP Flash Tool, Driver and Instruction manual.
  3. Launch the SP Flash Tool and locates Scatter File Tool.
  4. Now, you need to connect your Samsung SM-J100H with the computer and make a connection.
  5. Now click on upgrade and just wait for some time (minutes).
  6. Once the process successfully completed you will get a green signal.


    We hope this article will help you in solving the problems related to Samsung SM-J100H Flash File. And if it helps to solve your problem don’t forget to share with your friends and share your views about it.
    Download Link :: Link
    2:05 AM

    Samsung G935F Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

    Samsung G935F Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

    All Gsm Cracks Here Free :: Link
    Follow these steps to enter Download Mode/Odin Mode
    1. Power off your device
    2. Press and hold Volume Down key, Home Key and Power Key
    3. When your device vibrates, release Power key while keep holding the Volume Down key and Homekey
    4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
    5. You device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime you should see a light-blue box at the ID:COM section stating "COM:3" (the number depend on which USB port you have plugged the device cable and is irrelevant). Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either "PDA" or "Boot.img". After adding the file, click "Start" to begin the flashing process.
    6. WARNING DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
    7. When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device.
    8. Flash succeeded
    Samsung SAM G935F FRP Unlock ADB Enable File

    Download Link :: Link
    Samsung G935F Remove Pattern And Password Without Data Loss File
    Download Link :: Link
    Samsung Galaxy S7 Edge (G935F) Repair Imei Firmware And NG Network Fix File
    Download Link :: Link
    Samsung Galaxy S7 EDGE (G935F) Binary U2 6.0.1 Downgrade File
    Download Link :: Link
    Samsung G935F Galaxy S7 edge Binary U4 Tested Firmware Free File
    G935FXXS4ESCA_8.0
    Download Link :: Link
    Samsung G935F Galaxy S7 edge Binary U4 Combination Firmware File
    COMBINATION_FA60_G935FXXU4ASA2_CL7964511_QB21811149_REV00_user_mid_noship.tar
    Download Link :: Link 
    Samsung G935F Galaxy S7 edge Binary U5 Tested Firmware Free File
    SM-G935FXXS5ESDB_8.0_NBS_5FILE
    Download Link :: Link


    Downlaoad Link :: Link
    1:37 AM

    Samsung J106F Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

    Samsung J106F Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

    All Gsm Cracks Here Free :: Link
    Follow these steps to enter Download Mode/Odin Mode
    1. Power off your device
    2. Press and hold Volume Down key, Home Key and Power Key
    3. When your device vibrates, release Power key while keep holding the Volume Down key and Homekey
    4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
    5. You device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime you should see a light-blue box at the ID:COM section stating "COM:3" (the number depend on which USB port you have plugged the device cable and is irrelevant). Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either "PDA" or "Boot.img". After adding the file, click "Start" to begin the flashing process.
    6. WARNING DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
    7. When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device.
    8. Flash succeeded
    Downlaoad Link :: Link

    Wednesday, February 27, 2019

    7:35 PM

    Rivo Phantom Rx333 Mt6572 v4.4.2 Tested Scatter Firmware Flash File Free 100% Ok

    Rivo Phantom Rx333 Mt6572 v4.4.2 Tested Scatter Firmware Flash  File  Free 100% Ok 

    Flashing By Sp Flash Tool-CM2MTK-UMT And Any Other Tool
    No Dead Risk Dead Fix Virus Clear Hang On Logo Fix
    MT6572__alps__PHANTOM-RX333__zm88e_adks_od17e_emmc32_4_ddr2_b15_rx333__4.4.2__ALPS.KK1.MP7.Band1.2.5.V1.3

    How To Flash –Rivo Phantom Rx333

    Perfectly Working You Must Need to Follow Below


    1. Download Latest version Flash Tools
    2. Extract On Your Computer( Any Drive)
    3. Download You Mobile Same Version Firmware
    4. Extract On Your Computer
    5. Install Your Phone USB Driver On Your Pc
    6. Now Open SP Flash Tools On Your Pc
    7. Load Scatter File Frome Extract Firmware Location
    8. Click Download And Update Button
    9. Now Connect Your Phone With Your PC USB Cable
    10. Your Phone Star Flashing Wait for 5/7 Minute
    11. When Complete Flashing Process Then You Green Ring Will Paper
    12. Now Complete Your Phone Updated
    13. Remove USB Cable & Enjoy Mobile Phone
    14. Don’t Forget Comment & Share Thank You
    Warning Note: Fast Backup Your Phone Important Personal Data When Flash Your Phone Erase All Data File. So Please Fast Backup Data And Flashing Your Phone Own Risk.

    Motorola Rivo Phantom Rx333 Flash File



    Following are the steps to perform in order to Flash Stock Rom or any other custom ROM using so called flash tool SP(Smart Phone) Flash Device on a windows computer. Before starting the process of flashing make sure that your smartphone device has at least 50 percent of battery.

    1. Extract the flash file in any folder on your computer or laptop device.
    2. Need to install SP Flash Tool, Driver and Instruction manual.
    3. Launch the SP Flash Tool and locates Scatter File Tool.
    4. Now, you need to connect your  Rivo Phantom Rx333 with the computer and make a connection.
    5. Now click on upgrade and just wait for some time (minutes).
    6. Once the process successfully completed you will get a green signal.


      We hope this article will help you in solving the problems related to Rivo Phantom Rx333 Flash File. And if it helps to solve your problem don’t forget to share with your friends and share your views about it.
      Download Link :: Link
      6:56 PM

      Rivo Rhythm RX666 Dead Fix TESTED Firmware Flash File Free 100% Ok

      Rivo Rhythm RX666 Dead Fix TESTED Firmware Flash  File Free Download

      Flashing By Sp Flash Tool-CM2MTK-UMT And Any Other Tool
      No Dead Risk Dead Fix Virus Clear Hang On Logo Fix
      MT6580__RIVO__RHYTHM_RX666__RHYTHM_RX666__6.0__alps-mp-m0.mp1-V2.34_droi6580.weg.m_P29 By Atozflashfile.com By Raja Shoaib

      How To Flash –Rivo Rhythm RX666

      Perfectly Working You Must Need to Follow Below


      1. Download Latest version Flash Tools
      2. Extract On Your Computer( Any Drive)
      3. Download You Mobile Same Version Firmware
      4. Extract On Your Computer
      5. Install Your Phone USB Driver On Your Pc
      6. Now Open SP Flash Tools On Your Pc
      7. Load Scatter File Frome Extract Firmware Location
      8. Click Download And Update Button
      9. Now Connect Your Phone With Your PC USB Cable
      10. Your Phone Star Flashing Wait for 5/7 Minute
      11. When Complete Flashing Process Then You Green Ring Will Paper
      12. Now Complete Your Phone Updated
      13. Remove USB Cable & Enjoy Mobile Phone
      14. Don’t Forget Comment & Share Thank You
      Warning Note: Fast Backup Your Phone Important Personal Data When Flash Your Phone Erase All Data File. So Please Fast Backup Data And Flashing Your Phone Own Risk.


      Motorola Rivo Rhythm RX666 Flash File



      Following are the steps to perform in order to Flash Stock Rom or any other custom ROM using so called flash tool SP(Smart Phone) Flash Device on a windows computer. Before starting the process of flashing make sure that your smartphone device has at least 50 percent of battery.

      1. Extract the flash file in any folder on your computer or laptop device.
      2. Need to install SP Flash Tool, Driver and Instruction manual.
      3. Launch the SP Flash Tool and locates Scatter File Tool.
      4. Now, you need to connect your  Rivo Rhythm RX666  with the computer and make a connection.
      5. Now click on upgrade and just wait for some time (minutes).
      6. Once the process successfully completed you will get a green signal.


        We hope this article will help you in solving the problems related to Rivo Rhythm RX666 Flash File. And if it helps to solve your problem don’t forget to share with your friends and share your views about it.
        Download Link :: Link

        Monday, February 25, 2019

        7:33 AM

        Samsung J110H Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

        Samsung J110H Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working


        All Gsm Cracks Here Free :: Link
        Follow these steps to enter Download Mode/Odin Mode
        1. Power off your device
        2. Press and hold Volume Down key, Home Key and Power Key
        3. When your device vibrates, release Power key while keep holding the Volume Down key and Homekey
        4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
        5. You device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime you should see a light-blue box at the ID:COM section stating "COM:3" (the number depend on which USB port you have plugged the device cable and is irrelevant). Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either "PDA" or "Boot.img". After adding the file, click "Start" to begin the flashing process.
        6. WARNING DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
        7. When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device.
        8. Flash succeeded
        Downlaoad Link :: Link
        7:03 AM

        Samsung J200F Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

        Samsung J200F Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working


        All Gsm Cracks Here Free :: Link
        Follow these steps to enter Download Mode/Odin Mode
        1. Power off your device
        2. Press and hold Volume Down key, Home Key and Power Key
        3. When your device vibrates, release Power key while keep holding the Volume Down key and Homekey
        4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
        5. You device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime you should see a light-blue box at the ID:COM section stating "COM:3" (the number depend on which USB port you have plugged the device cable and is irrelevant). Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either "PDA" or "Boot.img". After adding the file, click "Start" to begin the flashing process.
        6. WARNING DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
        7. When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device.
        8. Flash succeeded
        Downlaoad Link :: Link
        6:35 AM

        SAMSUNG J120H Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

        SAMSUNG J120H Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

        SM-J120H Lock Screeen B0
        All Gsm Cracks Here Free :: Link
        Follow these steps to enter Download Mode/Odin Mode
        1. Power off your device
        2. Press and hold Volume Down key, Home Key and Power Key
        3. When your device vibrates, release Power key while keep holding the Volume Down key and Homekey
        4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
        5. You device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime you should see a light-blue box at the ID:COM section stating "COM:3" (the number depend on which USB port you have plugged the device cable and is irrelevant). Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either "PDA" or "Boot.img". After adding the file, click "Start" to begin the flashing process.
        6. WARNING DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
        7. When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device.
        8. Flash succeeded
        Downlaoad Link :: Link

        Sunday, February 24, 2019

        7:29 AM

        SM-J200H Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

        SM-J200H Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working


        All Gsm Cracks Here Free :: Link
        Follow these steps to enter Download Mode/Odin Mode
        1. Power off your device
        2. Press and hold Volume Down key, Home Key and Power Key
        3. When your device vibrates, release Power key while keep holding the Volume Down key and Homekey
        4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
        5. You device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime you should see a light-blue box at the ID:COM section stating "COM:3" (the number depend on which USB port you have plugged the device cable and is irrelevant). Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either "PDA" or "Boot.img". After adding the file, click "Start" to begin the flashing process.
        6. WARNING DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
        7. When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device.
        8. Flash succeeded
        Downlaoad Link :: Link

        Friday, February 22, 2019

        2:26 AM

        J320F Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

        J320F Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

        All Gsm Cracks Here Free :: Link
        Follow these steps to enter Download Mode/Odin Mode
        1. Power off your device
        2. Press and hold Volume Down key, Home Key and Power Key
        3. When your device vibrates, release Power key while keep holding the Volume Down key and Homekey
        4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
        5. You device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime you should see a light-blue box at the ID:COM section stating "COM:3" (the number depend on which USB port you have plugged the device cable and is irrelevant). Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either "PDA" or "Boot.img". After adding the file, click "Start" to begin the flashing process.
        6. WARNING DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
        7. When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device.
        8. Flash succeeded
        Downlaoad Link :: Link

        Wednesday, February 20, 2019

        11:44 PM

        Alcatel One Touch 7040D Stock Firmware ROM Tested Scatter Flash File

        Alcatel One Touch 7040D Stock Firmware ROM Tested Scatter Flash File

        No Dead Risk Virus Clear Hang On Logo Fix

        Complete Guide to Install Alcatel One Touch 7040D  Flash File




        Following are the steps to perform in order to Flash Stock Rom or any other custom ROM using so called flash tool SP(Smart Phone) Flash Device on a windows computer. Before starting the process of flashing make sure that your smartphone device has at least 50 percent of battery.

        1. Extract the flash file in any folder on your computer or laptop device.
        2. Need to install SP Flash Tool, Driver and Instruction manual.
        3. Launch the SP Flash Tool and locates Scatter File Tool.
        4. Now, you need to connect your Alcatel One Touch 7040D  with the computer and make a connection.
        5. Now click on upgrade and just wait for some time (minutes).
        6. Once the process successfully completed you will get a green signal.



          We hope this article will help you in solving the problems related to AAlcatel One Touch 7040D Flash File. And if it helps to solve your problem don’t forget to share with your friends and share your views about it.
          Download Link :: Link
          10:51 PM

          J320FN Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

          J320FN Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

          All Gsm Cracks Here Free :: Link
          Follow these steps to enter Download Mode/Odin Mode
          1. Power off your device
          2. Press and hold Volume Down key, Home Key and Power Key
          3. When your device vibrates, release Power key while keep holding the Volume Down key and Homekey
          4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
          5. You device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime you should see a light-blue box at the ID:COM section stating "COM:3" (the number depend on which USB port you have plugged the device cable and is irrelevant). Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either "PDA" or "Boot.img". After adding the file, click "Start" to begin the flashing process.
          6. WARNING DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
          7. When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device.
          8. Flash succeeded
          Downlaoad Link :: Link
          10:09 PM

          SM-J500F Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

          SM-J500F Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

          All Gsm Cracks Here Free :: Link
          Follow these steps to enter Download Mode/Odin Mode
          1. Power off your device
          2. Press and hold Volume Down key, Home Key and Power Key
          3. When your device vibrates, release Power key while keep holding the Volume Down key and Homekey
          4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
          5. You device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime you should see a light-blue box at the ID:COM section stating "COM:3" (the number depend on which USB port you have plugged the device cable and is irrelevant). Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either "PDA" or "Boot.img". After adding the file, click "Start" to begin the flashing process.
          6. WARNING DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
          7. When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device.
          8. Flash succeeded
          Downlaoad Link :: Link
          8:01 PM

          Alcatel One Touch Pixi 3 4013D Stock Firmware ROM Tested Scatter Flash File

          Alcatel One Touch Pixi 3 4013D Stock Firmware ROM Tested Scatter Flash File

          No Dead Risk Virus Clear Hang On Logo Fix

          Complete Guide to Install Alcatel One Touch Pixi 3 4013D  Flash File




          Following are the steps to perform in order to Flash Stock Rom or any other custom ROM using so called flash tool SP(Smart Phone) Flash Device on a windows computer. Before starting the process of flashing make sure that your smartphone device has at least 50 percent of battery.

          1. Extract the flash file in any folder on your computer or laptop device.
          2. Need to install SP Flash Tool, Driver and Instruction manual.
          3. Launch the SP Flash Tool and locates Scatter File Tool.
          4. Now, you need to connect your Alcatel One Touch Pixi 3 4013D  with the computer and make a connection.
          5. Now click on upgrade and just wait for some time (minutes).
          6. Once the process successfully completed you will get a green signal.


            We hope this article will help you in solving the problems related toAlcatel One Touch Pixi 3 4013D Flash File. And if it helps to solve your problem don’t forget to share with your friends and share your views about it.
            Download Link :: Link

            Tuesday, February 19, 2019

            7:37 AM

            SM-J500FN Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

            SM-J500FN Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

            Follow these steps to enter Download Mode/Odin Mode
            1. Power off your device
            2. Press and hold Volume Down key, Home Key and Power Key
            3. When your device vibrates, release Power key while keep holding the Volume Down key and Homekey
            4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
            5. You device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime you should see a light-blue box at the ID:COM section stating "COM:3" (the number depend on which USB port you have plugged the device cable and is irrelevant). Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either "PDA" or "Boot.img". After adding the file, click "Start" to begin the flashing process.
            6. WARNING DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
            7. When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device.
            8. Flash succeeded
            Downlaoad Link :: Link

            Sunday, February 17, 2019

            6:56 AM

            SM-J500H Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

            SM-J500H Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

            Follow these steps to enter Download Mode/Odin Mode
            1. Power off your device
            2. Press and hold Volume Down key, Home Key and Power Key
            3. When your device vibrates, release Power key while keep holding the Volume Down key and Homekey
            4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
            5. You device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime you should see a light-blue box at the ID:COM section stating "COM:3" (the number depend on which USB port you have plugged the device cable and is irrelevant). Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either "PDA" or "Boot.img". After adding the file, click "Start" to begin the flashing process.
            6. WARNING DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
            7. When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device.
            8. Flash succeeded
            Downlaoad Link :: Link

            Saturday, February 16, 2019

            8:41 AM

            SM-J510F Remove Pattern And Password Without Data Loss File Flash Only Odin

            SM-J510F Remove Pattern And Password Without Data Loss File Flash Only Odin 100% Working

            Follow these steps to enter Download Mode/Odin Mode
            1. Power off your device
            2. Press and hold Volume Down key, Home Key and Power Key
            3. When your device vibrates, release Power key while keep holding the Volume Down key and Homekey
            4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
            5. You device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime you should see a light-blue box at the ID:COM section stating "COM:3" (the number depend on which USB port you have plugged the device cable and is irrelevant). Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either "PDA" or "Boot.img". After adding the file, click "Start" to begin the flashing process.
            6. WARNING DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
            7. When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device.
            8. Flash succeeded
            Downlaoad Link :: Link
            J510F 7.1.1 U2 REMOVE SCREEN LOCK
            Download Link :: Link 1 :: Link 2 :: Link 3
            disable copy paste.txt Displaying disable copy paste.txt.