Breaking

Monday, September 23, 2019

7:01 AM

Samsung G930F U6 8.0.0 Root Frp Off Oem Off File

Samsung G930F U6 8.0.0 Root Frp Off Oem Off File
                                        

  1. You will then be able to get Odin V3.1.0 and Samsung G930F U6 8.0.0 Root Frp Off Oem Off File after extracting the zip file.
  2. Power off your Samsung device.
  3. Then, press and hold Power Key, Home Key, and Volume Down Key at the same time.
  4. When prompted as shown, press the Volume Up key to continue the process and you will enter Download Mode.
  5. Step 2 Perform Odin3 and Connect Samsung Device to PC.
  6. Launch Odin3, and connect your Samsung via USB cable to PC.
  7. Once you have connected your handset to the computer, Odin3 will automatically recognize the device and prompt "Added" in the lower-left panel.
  8. Now, click on the "AP/PDA" button and select the file extracted in advance.
  9. After that, click on the "Start" button to begin the rooting process.
  10. It will take a few seconds to finish rooting, and when it finished, the green "PASS" will inform you that the rooting process is finished.
  11. When your Samsung phone is on anew, there will be a SuperSu app showed on the screen which means you've succeeded in rooting.
  12. Besides, you can check out the root status by using
  13. What if it fails to get root on your Samsung phone, check out the solutions below.
  14. 1. Restart your PC and install Samsung USB Driver, and try to reconnect.
  15. That's all about getting rooted in Samsung phones with Odin3.

How to Flash


  1. Download the relevant USB driver for your Samsung device.
  2. Download the flash tool Odin on your phone.
  3. Now, download the relevant ADB Enable File for your device.
  4. Open the Odin software then choose ADB Enable File in “AP” from the Box.
  5. Turn on USB debugging mode on your phone.
  6. Now, connect your mobile and computer with a USB cable.
  7. Open the ADB Enable tool and click on the start. After that, your device will start rebooting.
  8. Disconnect the USB cable.
  9. Select language English when your phone turns on. After that, click next.
  10. Now turn on Wi-Fi or mobile data.
  11. After that, agree on the agreements and click on next. They will ask you to verify your account.
  12. Now, connect your mobile and PC again. Then open the Atozflashfile.com..
  13. You will see some information about your mobile phone and the operating system.
  14. Click on remove FRP. The lock will be removed in a short time.
  15. Congratulations, you have successfully bypassed the FRP lock.


  • right-click to "Open as Administrator"

Follow these steps to enter Download Mode/Odin Mode
  1. Power off your device
  2. Press and hold Volume Down key, Home Key and Power Key
  3. When your device vibrates, release Power key while keep holding the Volume Down key and the Home key
  4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
Your device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime, you should see a light-blue box at the ID: COM section stating "COM:3" (the number depending on which USB port you have plugged the device cable and is irrelevant).

Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either BL"AP"CP"CSC
After adding the file, click "Start" to begin the flashing process
Click "Start" to flash.
DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device
Flash succeeded

Samsung G930F Galaxy S7 U4 Android 8.0 Root Repair Imei Flash File / Firmware
Samsung Galaxy S7 (G930FD) 8.0 Root Tested Root File
Samsung G930F U6 8.0.0 Root Frp Off Oem Off File

Thursday, September 19, 2019

4:59 AM

Samsung J710F EMMC DUMP File

Samsung J710F EMMC DUMP File
                                     

SM-J701F(NRD90M.J701FXXU2AQI3-7.0-NRD90M)[AJTD4R_B74FECB2] EMMC DUMP

How To Flash:

1: Download and install the device driver software on your computer.
2: Download and extract the Stock ROM (Official/Original Firmware).
3: Download and extract Odin on your PC.
4: Boot your Samsung device into Download mode.
Power off your device
Press and hold Volume Down key, Home Key and Power Key
When your device vibrates, release Power key while keep holding the Volume Down key and the Home key
Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
5: Connect your device to PC then Device is connected to Odin.
6: Click "PDA" or "AP" to add a tar.md5 file that you have extracted and then "Start"



Samsung J701F  Galaxy J7 Binary U6 Core Reset FRP Tested File 
J701F U3 Enable ADB Remove FRP

Samsung J701F  Galaxy J7 Binary U3 Core Reset FRP  File 

 Link
Samsung J701F U6 EngBoot Flash File  Firmware
Link
Samsung J701F U5 EngBoot Flash File  Firmware
Link
Samsung J701F U6 Android 8.1.0 Reset Frp Flash File  Firmware
Link
Samsung J710F EMMC DUMP File
Download Link:: Link 
1:12 AM

Samsung ROOT A105F U1,U3 Flash File

Samsung ROOT A105F U1, U3 Flash File
                                                   
  1. You will then be able to get Odin V3.1.0 and ROOT_A105F_U1_9  after extracting the zip file.
  2. Power off your Samsung device.
  3. Then, press and hold Power Key, Home Key, and Volume Down Key at the same time.
  4. When prompted as shown, press the Volume Up key to continue the process and you will enter Download Mode.
  5. Step 2 Perform Odin3 and Connect Samsung Device to PC.
  6. Launch Odin3, and connect your Samsung via USB cable to PC.
  7. Once you have connected your handset to the computer, Odin3 will automatically recognize the device and prompt "Added" in the lower-left panel.
  8. Now, click on the "AP/PDA" button and select the file extracted in advance.
  9. After that, click on the "Start" button to begin the rooting process.
  10. It will take a few seconds to finish rooting, and when it finished, the green "PASS" will inform you that the rooting process is finished.
  11. When your Samsung phone is on anew, there will be a SuperSu app showed on the screen which means you've succeeded in rooting.
  12. Besides, you can check out the root status by using
  13. What if it fails to get root on your Samsung phone, check out the solutions below.
  14. 1. Restart your PC and install Samsung USB Driver, and try to reconnect.
  15. That's all about getting rooted in Samsung phones with Odin3.
ROOT A105F U1 9
Download Link:: Link
ROOT A105F U3 9
Download Link:: Link
ROOT A105FDDU U3 9
Download Link:: Link
ROOT A105FPUU U3 9
Download Link:: Link

Tuesday, September 17, 2019

7:59 PM

Samsung J400F U4 Flash File

Samsung J400F U4 Flash File
                            
Samsung J400F Galaxy J4 Flash File (Binary: U4-J400FXXU4BSF4_9.0_MID_5FILE). Fix Bootloop, fix hang logo, bypass frp, repair IMEI... Samsung J400F Combination File is a raw Firmware for engineers and developers to run the device&can fully Read and test the equipment of the device Samsung.

Samsung Galaxy SM-J400F

Flash File ROM is still limited to Boot Security and sometimes it keeps FRP lock, EE, and other securities. Basically, It’s only for testing devices and fixing a few software problems. So, once the problem has been Fixed, We Have To Flash the stock official ROM to make the device working again.

How to Flash



  1. Download the relevant USB driver for your Samsung device.
  2. Download the flash tool Odin on your phone.
  3. Now, download the relevant ADB Enable File for your device.
  4. Open the Odin software then choose ADB Enable File in “AP” from the Box.
  5. Turn on USB debugging mode on your phone.
  6. Now, connect your mobile and computer with a USB cable.
  7. Open the ADB Enable tool and click on the start. After that, your device will start rebooting.
  8. Disconnect the USB cable.
  9. Select language English when your phone turns on. After that, click next.
  10. Now turn on Wi-Fi or mobile data.
  11. After that, agree on the agreements and click on next. They will ask you to verify your account.
  12. Now, connect your mobile and PC again. Then open the Atozflashfile.com..
  13. You will see some information about your mobile phone and the operating system.
  14. Click on remove FRP. The lock will be removed in a short time.
  15. Congratulations, you have successfully bypassed the FRP lock.

  • right-click to "Open as Administrator"

J400FXXU4BSF4_9.0_MID_5FILE
Follow these steps to enter Download Mode/Odin Mode
  1. Power off your device
  2. Press and hold Volume Down key, Home Key and Power Key
  3. When your device vibrates, release Power key while keep holding the Volume Down key and the Home key
  4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
J400FXXU4BSF4_9.0_MID_5FILE
Your device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime, you should see a light-blue box at the ID: COM section stating "COM:3" (the number depending on which USB port you have plugged the device cable and is irrelevant).

J400FXXU4BSF4_9.0_MID_5FILE
Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either BL"AP"CP"CSC
J400FXXU4BSF4_9.0_MID_5FILE
After adding the file, click "Start" to begin the flashing process
J400FXXU4BSF4_9.0_MID_5FILE
Click "Start" to flash.
DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device
Flash succeeded

Samsung J400F ENG Modem Binary U4 File
Samsung Galaxy J4 SM-J400F U4 9.0 Root Flash File Firmware
Link
Samsung J400F Galaxy J4 Binary U4 Combination File
Link
Samsung J400F Galaxy J4 Binary U4 Flash File Firmware
Download Link:: Link
Password::Atozflashfile.com
03002947655
6:11 AM

Samsung G928A Galaxy S6 Edge+ Cert File

Samsung G928A Galaxy S6 Edge+ Cert File
CERT file is unique for every phone and contains a signature.
This file exists in the Samsung database from the day of the product your phone.

For Qualcomm device you cannot READ CERT but can only WRITE CERT from who have one from his device and Share it, (obviously not in the same country/operator itc..), or from any server that will seller these.
You do not damage your device if CERT is good,
BUT
FIRST MUST NEED OF CANCEL ORIGINAL CERT, the only mode for do it is Wiping EFS and after WRITE new one.

For Exynos devices You can READ/WRITE CERT.
A To Z Flash File
A To Z Flash File

NOTE:
FOR QUALCOMM, YOU CAN WRITE CERT FROM OTHER N900 to OTHER N900X IF THIS HAVE "CERT" WITH FULL UNLOCKED AND IMEI/NETWORK OK!!!
A To Z Flash File


Samsung G928A Galaxy S6 Edge Eng Boot File
Download Link:: Link 1:: Link 2
Password::Atozflashfile.com

03002947655

Monday, September 16, 2019

4:05 AM

Q Mobile Power 4000 mini Flash File

Q Mobile Power 4000 mini Flash File
Requirements For Flashing

I:- Download and install SPD USB Mobile driver
II:- Download and install Mobile supported box / Dongle setup like Infinity Cm2
How to Flash

  • Download and install SPD USB Mobile drivers
  • Download Flash File From Link and extract it
  • Open supported box setup / Dongle.
  • Select Correct Mobile CPU type From Setup and Choose flash file.
  • Turn off the Mobile, remove the battery.
  • Connect the Cellphone with USB data cable through Computer and insert a Mobile battery again.
  • Press and hold Mobile Boot Key
  • Click on flash & then wait for the complete flash
  • Complete Flash remove USB data cable and power on the device.
  • Enjoy it has done.
Note: Please make a back up of your device before install or update Flashing File.
Download Link:: Link
Password::Atozflashfile.com
03002947655

Sunday, September 15, 2019

1:24 AM

Rivo C15 Flash File

Rivo C15 Flash File

All Gsm Crack Tool 100% Tested Here:: Link

How To Flash MTK Keypad Phone



  1. First of all, you need to download and install MTK USB drivers on PC.
  2. After that, you need to download the correct flash file for your phone, the file should be in BIN format.
  3. Use any MTK flashing tool for the flash BIN file.
  4. Popular MTK BIN file flashing tools are  CM2 Dongle
  5. Note: Please backup firmware before flashing. We are not responsible for any damage caused to your phone.
     Download Link:: Link 1:: Link 2
      Password::Atozflashfile.com
      03002947655

Saturday, September 14, 2019

10:35 AM

Samsung J400F Galaxy J4 Binary U4 Combination File

Samsung J400F Galaxy J4 Binary U4 Combination File
                                       
Samsung J400F Galaxy J4 Combination File (Binary: U4-J400FXXU4ASG1). Fix Bootloop, fix hang logo, bypass frp, repair IMEI... Samsung J400F Combination File is a raw Firmware for engineers and developers to run the device&can fully Read and test the equipment of the device Samsung.

Samsung Galaxy SM-J400F

Combination ROM is still limited Boot Security and sometimes it keeps FRP lock, EE, and other securities. Basically, It’s only for testing devices and fixing a few software problems. So, once the problem has been Fixed, We Have To Flash the stock official ROM to make the device working again.

How to Flash

  1. Download the relevant USB driver for your Samsung device.
  2. Download the flash tool Odin on your phone.
  3. Now, download the relevant ADB Enable File for your device.
  4. Open the Odin software then choose ADB Enable File in “AP” from the Box.
  5. Turn on USB debugging mode on your phone.
  6. Now, connect your mobile and computer with a USB cable.
  7. Open the ADB Enable tool and click on the start. After that, your device will start rebooting.
  8. Disconnect the USB cable.
  9. Select language English when your phone turns on. After that, click next.
  10. Now turn on Wi-Fi or mobile data.
  11. After that, agree on the agreements and click on next. They will ask you to verify your account.
  12. Now, connect your mobile and PC again. Then open the Atozflashfile.com..
  13. You will see some information about your mobile phone and the operating system.
  14. Click on remove FRP. The lock will be removed in a short time.
  15. Congratulations, you have successfully bypassed the FRP lock.

  • right-click to "Open as Administrator"

COMBINATION_FAC_FA80_J400FXXU4ASG1
Follow these steps to enter Download Mode/Odin Mode
  1. Power off your device
  2. Press and hold Volume Down key, Home Key and Power Key
  3. When your device vibrates, release Power key while keep holding the Volume Down key and the Home key
  4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
COMBINATION_FAC_FA80_J400FXXU4ASG1
Your device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime, you should see a light-blue box at the ID: COM section stating "COM:3" (the number depending on which USB port you have plugged the device cable and is irrelevant).

Samsung G965F Binary U6 Combination File
COMBINATION_OXM_FA80_G965FXXU6ASG2
Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either BL"AP"CP"CSC
COMBINATION_FAC_FA80_J400FXXU4ASG1
After adding the file, click "Start" to begin the flashing process
COMBINATION_FAC_FA80_J400FXXU4ASG1
Click "Start" to flash.
DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device
Flash succeeded

Samsung J400F ENG Modem Binary U4 File
Samsung Galaxy J4 SM-J400F U4 9.0 Root Flash File Firmware
Link
Samsung J400F Galaxy J4 Binary U4 Flash File Firmware
Link
Download Link:: Link
Password::Atozflashfile.com
03002947655

Wednesday, September 11, 2019

8:09 PM

Samsung G965F Binary U6 Combination File

Samsung G965F Binary U6 Combination File
COMBINATION_OXM_FA80_G965FXXU6ASG2
Samsung Galaxy S9 Plus SM-G965F Combination File (Binary: U6-G965FXXU6ASG2). Fix Bootloop, fix hang logo, bypass frp, repair IMEI... Samsung G965F Combination File is a raw Firmware for engineers and developers to run the device&can fully Read and test the equipment of the device Samsung.

Samsung Galaxy SM-G965F

Combination ROM is still limited Boot Security and sometimes it keeps FRP lock, EE, and other securities. Basically, It’s only for testing devices and fixing a few software problems. So, once the problem has been Fixed, We Have To Flash the stock official ROM to make the device working again.
How to Flash

  1. Download the relevant USB driver for your Samsung device.
  2. Download the flash tool Odin on your phone.
  3. Now, download the relevant ADB Enable File for your device.
  4. Open the Odin software then choose ADB Enable File in “AP” from the Box.
  5. Turn on USB debugging mode on your phone.
  6. Now, connect your mobile and computer with a USB cable.
  7. Open the ADB Enable tool and click on the start. After that, your device will start rebooting.
  8. Disconnect the USB cable.
  9. Select language English when your phone turns on. After that, click next.
  10. Now turn on Wi-Fi or mobile data.
  11. After that, agree on the agreements and click on next. They will ask you to verify your account.
  12. Now, connect your mobile and PC again. Then open the Atozflashfile.com..
  13. You will see some information about your mobile phone and the operating system.
  14. Click on remove FRP. The lock will be removed in a short time.
  15. Congratulations, you have successfully bypassed the FRP lock.

  • right-click to "Open as Administrator"

Samsung G965F Binary U6 Combination File
COMBINATION_OXM_FA80_G965FXXU6ASG2
Follow these steps to enter Download Mode/Odin Mode
  1. Power off your device
  2. Press and hold Volume Down key, Home Key and Power Key
  3. When your device vibrates, release Power key while keep holding the Volume Down key and the Home key
  4. Press Volume Up key to enter Download mode, which has a green robot figure and “Downloading… Do not turn off target!!)
Samsung G965F Binary U6 Combination File
COMBINATION_OXM_FA80_G965FXXU6ASG2
Your device should be automatically recognized by Odin. At the lower-left of Odin interface, it should show a message that says "Added!" and in the meantime, you should see a light-blue box at the ID: COM section stating "COM:3" (the number depending on which USB port you have plugged the device cable and is irrelevant).

Samsung G965F Binary U6 Combination File
COMBINATION_OXM_FA80_G965FXXU6ASG2
Whether it is "PDA" or "AP" depends on the version of Odin that you used. But the md5 file goes to either BL"AP"CP"CSC
Samsung G965F Binary U6 Combination File
COMBINATION_OXM_FA80_G965FXXU6ASG2
After adding the file, click "Start" to begin the flashing process
Samsung G965F Binary U6 Combination File
COMBINATION_OXM_FA80_G965FXXU6ASG2
Click "Start" to flash.
DO NOT REMOVE OR OPERATE ON YOUR DEVICE UNTIL FINISHED OR FAILED IS SHOWED ON ODIN.
When the flashing process is done and if everything goes well, you should see a big green box saying "RESET" or "PASSED" (depends on the version of Odin is used). By now, the device should be rebooted and it is safe to remove/unplug your device
Flash succeeded
Download Link:: Link
Password::Atozflashfile.com
03002947655